|
2#
楼主 |
发表于 2009-4-2 07:25:56
|
只看该作者
BASIC REQUIREMENTS FOR CONVERTING TO WATERBORNE INKS
At the outset, machine and personnel problems arose with regard to the use of waster
technology. This required new perspectives and modification of the flexographic printing press
and its functional components.
1. The ink transfer system requires attention to ensure the metering capabilities of the
components and the structural nature of the rollers. Changes in the rollers are required
because of the nature of the water ink (it tends to be somewhat like a high solids ink), as
well as the need to use less solvent (water) to facilitate drying. Potential corrosion and
abrasion necessitates a close look at the materials from which the anilox roller is made.
It is imperative that the metering rollers are in continuous motion when the water inks
are in the printing station. Re-wetting of all surfaces is critical as dried water ink is like
cement. This is most important during press stoppages. Older press configurations and
in- line units do not always have this feature and must be modified. At the same time,
provisions must be made to automatically move the plate cylinder away from the anilox
roll when the press stops.
Fountain(Ink) and anilox rollers in the ink transfer systems have to be replaced with
new rollers that have properties that will facilitate the use of the water formulated inks.
The fountain roller carries the ink from the ink reservoir (pan) to the metering roller
(anilox). The harder the durometer of the rubber covering on the roll, the less ink the
roller will transfer. Where the standard rubber covering for solvents is between 65-75
Durometer, Shore A, the hardness required for water inks is in the 85-90 Durometer
range.
The anilox roller is engraved with cells that meter and transfer the inks. The finer the
screen (cells per inch) and the shallower the etch, the less ink that will be transferred.
For example, a 360 screen would deliver a much finer layer and lesser quantity of ink
and solvents than would a 200 screen. A similar screen but lower volume will
effectively reduce the amount of ink transferred.Water-based inks have higher pigment
concentrations by volume that solvent-based inks. Therefore, less water-based ink
volume is required on the printing plate. Anilox roll cells should be adjusted
accordingly. The net result is less ink volume used.
Drying systems that were more than adequate with hydrocarbon solvents can be totally
inadequate for water. The typical flexo dryer box had air flowing into the constrained
area, bouncing off the walls and through slots or holes onto the web. This was adequate
with a solvent that evaporated quickly and could be removed by a slightly higher exhaust
air flow.
Water inks posed two problems. One was the volume of the vapors from the water -
essentially 10 times the volume of- solvent given the same liquid volume as a starting
point. Second, amines required in the formulations to hold the resins and pigments in
suspension. If the amines are not completely removed by a scrubbing action, they can
remain in the ink layer and soften subsequent layers of inks that may be printed in
succession.
Drying systems have to be rebuilt or equipped with better air movement and much
higher exhaust rates.
Drying speed is also a factor. A slow press will not require as much air flow. Production
on a high-speed press will be limited if the air flow is not adequate. A general finding
with water inks on existing high-speed presses is the loss of 25% to 30% of the
production speed when run with drying systems designed for solvent-based inks.
Dryers designed for water-based inks feature different airflows. The best designs have
sought to generate a scrubbing action to remove the amines and water, and high
velocity to evacuate the vapors.
3. Film surfaces must be post-treated at the press to raise the surface tension during
printing. Post-treating units (Corona or Flame) are required to bombard the surface of
the film and make it more receptive to the waterborne inks.
The corona treatment not only raises the surface tension of the film surface, making it
more receptive to ink wetting out and adhesion; it either causes the slip compound to
retreat into the film surface temporarily or moves the slip around enough to “wet” out the
inks.
4. A new development in flexo press design has become a major consideration for the
printer using water, namely the replacement of the fountain roller with an enclosed
doctor blade system. More recently a further refinement of the chamber doctor blade
system enables the flexo printer to do an automatic cleanup of the ink train.
Instead of having the ink fed from an open fountain to the anilox roller by a rubber roller,
the doctor blade system has its ink injected into a reservoir that consists of the cavity
formed by the anilox roller, a retaining blade and a cutting blade. The cutting blade
shears off all unwanted ink from the rotating surface of the roller as the ink is
transferred to the printing plate.
Not only does this system improve the quality of the printing, it eliminates a major area of
both captured and fugitive emissions by removing the open fountain. By enclosing the
layer of ink (and water) being transferred, the system reduces the amount of diluent that
will vaporize in the press operation.
The latest innovation provides for an air-powered wash cycle that cleans out the unit and
the anilox roller, and minimizes both waste ink and washwater (or solvent).
5. Coupled with the above major mechanical changes in equipment are those necessitated
in auxiliary systems:
a. Ink pumps that were used with solvent inks are not compatible with
water. The fast impeller speed promotes foaming of the water inks. New
pumps must be obtained.
b. Printing plates may have to be changed to different rubber or
photopolymer base material having surface tensions that will accept and
transfer inks more adequately.
c. Solvent recovery equipment, normally distillation units, which were
used for solvents, are not feasible for reclamation of water inks. New
technology, i.e. evaporation or ultrafiltration, or the off-site removal of this
waste, may be required.
6. Films and paper/paperboard that have coatings will require compatibility with water inks.
Too often, a solvent or UV curable ink system will not anchor to coatings that have been
developed for solvent inks. Consult your ink/coating company for assistance.
7. Personnel must be trained to utilize new methods in the setting up and cleaning of
presses to ensure that inks do not dry on the rollers, on plates, or other parts of the
machinery.
A major effort has to be made in the methods used in setting up, operating and breaking
down presses. The transfer characteristics of waterborne inks are such that the work
force has to be completely trained in the use and troubleshooting of the new inks.
Solvents were very forgiving; water inks are not.
The drying of waterborne inks results in a solid that is difficult to remove. To avoid loss of
rollers and gears, as well as damage to cylinders and impression drums (cylinders), the
pressroom personnel have to be convinced of the need to clean any spills, as well as all
rollers and plates when the press is down for changes or any extended downtime.
8. Obtain a complete technical profile of the substrate to be printed. Various polymers,
coatings and additives (for example, slip agents), may be more or less receptive to water
inks. Knowing the limitations can help you to use the appropriate substrates or treat the
materials in a manner that will facilitate wetting and adhesion of the inks.
Research and development efforts are most needed in this area. Little has been done or
published with regard to the ramifications of using various slip agents and anti-block
additives on films printed with waterborne inks. The same can be said of coatings used
to promote adhesion to films and foils.
Supporting Documentation
To give a more complete picture of the status of waterborne inks and the technology required to
make them work, I refer you to articles and papers delivered at programs and printed in the
various trade journals and magazines such as American Inkmaker, Converting, and Paper,Film
and Foil Converter. These papers were delivered by some of the leading experts in the field,
and should help to foster a better understanding of why water can work and what it takes to
make that effort successful.
Fred Shapiro authored this fact sheet. |
|