|
Quiz no 1
1.
list 5 duties of a paint inspector.
- To conform and secure that corrosion protection by protective coatings are carried out according to the specification and relevant standards;
- To check and observe;
- To monitor;
- To report;
- To act safety and keep up with developments within
the field of corrosion; - Generally to carry out all duties specified in the contract or specification.
2.
what is the difference between steel preparation and surface preparation?
- Steel preparation = comprise all necessary works in order to remove all steel structure defects: laminations; pittings; sharp edges; slags; welds defects (pores, undercuts)
prior to surface preparation. - Surface preparation = comprise all necessary methods, mechanical or by hand, to obtain
a sound area to apply paints on.
3. various types of surface contamination are frequently found on
surface to be painted.
A. Please list a minimum five of these types of contamination.
- Oil/grease; mill scale;rust;old paint and water soluble substances.
B. How would you check a surface to be blasted in order to determine if
The surface is contaminated with oil?
- By “water on the goose” method which consist in sprinkling
Water on the surface suspected and if water forms small droplets
It is highly certain that is contaminated with oil.
4. an abrasive blast cleaned steel surface to be immersed in sea water is contaminated with sodium chloride in excess of 200 mg/sqm. The surface is overcoated with an epoxy mastic system (3x100 mic). Upon immersion in water, blistering will start after a period of time.
A. Would you assume that the size of the blisters would be greater in fresh water than sea water, or would you assume the opposite? Please state your reasons?
·
The size of blistering will be greater due to the fact that fresh water has low salt content and in time will permeates the lining system placed in immersion and will
disolve the nacl forming a solution with high salt to water ratio.the high the purity of the water the greater the tendency for osmotic blistering .this difference in salt concentration leads to what is called “osmotic driving force” which increases the rate of water permeation from bulk liquid side to the entrapped solution side in order to create an equilibrium accomplished when sufficient moisture from the bulk side permeates the lining system such that the salt concentration on either side of lining system (semipermeable membrane) is equalised. In practice, this never occurs due to the rapid drop off of osmotic driving force after innitial permeation occurs and the inelasticity of the lining material.
B. What do we call this type of blistering?
5. blasting abrasives are commonly classified in four main groups.
A. Please name at least three of these four main classification groups.
- Minerals-natural;
- Minerals-artificial;
- Metallic;
- Organic.
B. Please name at least two examples of abrasives from each of the classification groups listed under a. Above.
- Sands=silica ;garnet; olivine
- Slags = copper; iron; aluminium;silicon carbides;
- Steel = grit ; shots; wire chops; bronze shots;
- Nylon pearls; polyestirene; coconut or walnut shells (ground).
6. blasting abrasives may sometimes be contaminated, and the two most common contaminants are oil/fat and sodium chloride. Please describe the procedure for checking blasting abrasives for determination of contamination with:
A. Oil/fats.
- Using some of the facilities listed below and visualizing the changes into solution.
B. Water soluble salts.
·
It is a mandatory procedure for testing the abrasives and must be carried out both in nb or m&r before blasting commence.for the test to be performed it needs the following: a conductivity meter;two glasses or plastic beakers (1=400 ml and 1=100 ml); a gradueted measuring cylinder of 250 ml; a supply of distilled water with conductivity of less than 2 ms/cm-1; a supply of calibration solution, consisting of 0.5 grammes of nacl in 1000 ml of distilled water maded in laborratory;rubber gloves; stirring rod; a funnel; filter papers; plastic bags; a stop watch; quantab chloride test papers ( to verifythat the high reading, when the abrasive test sample exceeds 300 ms/cm-1,is caused mainly by nacl rather than sodium sulphate. It will measure only the nacl)
1. fill the graduated measuring cylinder with 200 mg of abrasive sample and transfer into 400ml beaker; 2.fill the same cylinder with 200 ml distilled water and transfer to the 400 ml beaker; 3.stirr the abrasive and water with the rod one minute and allow the mixture to stand for eight minutes and stir again for one minute.these ten minutes are very important because it ensures the soluble salts have time to dissolve; 4. filter the liquid into the 100 ml beaker through the funnel discarding the first 10 ml. 50 ml should be collected for the test; 5. to take the conductivity reading immerse the probe in the test solution and note the reading displayed.the gage should be adjusted in the mode of microsiemens per centimetre. Less than 50 ms/cm-1 = accepted; less than 150 = accepted; less than 300 =acceptable but should be tested with quantab chloride paper; more than 300 = rejected without using any further testing. More than 2.8 units=rejected less than 2.8 accepted.
the compressed air used for blasting may also be contaminated with oil and or water.
C. Please describe the method by which the compressed air may be checked for content of oil or water.
- Performing the blotter test. For one minute a white blotter or cloth is held withiin 60 cm of the end of an operating air line. If will be observed dark spots or condensation means that the oil/water is carried in the blasting air. And oil/moisture trap should be installed at the output line.
7. abrasive blast cleaning of steel surfaces are carried out in accordance to internationally accepted standards. Please name (by designation and number) the standards used for:
A. Determination of metal cleanliness
- Nace = no1 (white metal); no2 (near white metal); no3 (commercial).
- Iso 8501-1 = sa 3 ; sa2 ½
; sa 2. - Sspc = sspc 5; sspc 10; sspc 6.
B. Determination of metal roughness
- Iso 8503 -1. roughness comparators.choose comparator according to abrasive type. G = grit; s = shots and place the comparator on the steel surface and observe through the center hole.take the readings. Ry = fine(25-50 mic) segm 1-2 ;medium (50-85 mic) segm 2-3 and coarse(85-130mic) segm 3-4.
8. various types of abrasives are used for different purposes. Name the abrasive types most suited for:
A.
Blast cleaning of stainless steel
- Garnet = non-metallic and organic = tomoid metal dust
B.
Centrifugal blast cleaning of steel profiles.
- Steel shots; steel grit; steel wire chops.
老大给升精了,再补充一些
The 99 questions
1.
What condition is essential for galvanic (bimetallic) corrosion to occur?
Oxygen; electrolyte; (two metals having) different potentials
2.
How do we recognize turbulence corrosion?
In copper we can find sharply defined pits which commonly are undercut on the side facing the water’s direction of flow
3. When we use the term degraphitation of cast iron, what kind of corrosion do we refer to ?
Selective corrosion
4. Degraphitation is a special form of bimetallic corrosion and either iron or the steel is consumed
through dissolution. Which of the two substances will go to dissolution?
Iron (will sacrifice itself for graphite leaving the surface as a layer. This layer has no
mechanical strength, however the object looks intact. The graphite may be easily removed with
e.g. a knife.
5. Most of coatings function by the barrier principal. Against what is the coating barrier?
(against) liquid; water and partly oxygen
[ 本帖最后由 djb_19814444 于 2008-5-21 20:19 编辑 ] |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册
x
|