聚合物型成膜助剂 WP 8, 零VOC

赛比克

PLASTICIZER *  WP 8





NON-VOLATILE, NON HYDROLYSABLE
POLYMERIC PLASTICIZER




INTRODUCTION :

PLASTICIZER WP 8 is a non-volatile, low viscosity polymeric film-forming agent that was originally, specifically developed for plasticizing acrylic polymers.

Due to its structure, PLASTICIZER WP 8 combines totally high hydrolysis resistant properties with hydrophobicity.



CHARACTERISTICS :

Appearance   2O° C                  Clear liquid
Active ingredients (%)                  100
Boiling-point (° C)                  286
Density                  ca. 1.1
Viscosity 25°C (cps)                  ca. 60
Flash-point (open-cup / ° C)                  199
Solubility                  insoluble in water
                soluble in mos                organic solvents


PROPERTIES :

PLASTICIZER WP 8 is compatible with acrylics, epoxies, alkyds, polyesters, rosin derivatives and phenolics.

PLASTICIZER WP 8 imparts the following properties :

        -        outstanding elongation and recovery
        -        increase in flexibility and toughness
        -        decrease in brittleness
        -        very low water sensitivity
        -        improvement in film formation
        -        resistance to mildew growth.



Unlike many other types of plasticizers, PLASTICIZER WP 8does not adversely affect the adhesion, consistency, pigment binding power or package stability of acrylic latex caulks. Its excellent compatibility with acrylic dispersions allows considerable latitude regarding the amounts that may be used.

According to the type of application, the level of PLASTICIZER WP 8may vary from 1 % to more that 10 % on the end formulation.

The ability of PLASTICIZER WP 8to reduce the Minimum Film Forming Temperature (MFFT) is shown below :





APPLICATIONS :

PLASTICIZER WP 8 is mainly used in the following end-applications :

        -        caulks and sealants (see attached formulation)
        -        sealers / topcoats for wood (see attached formulation)
        -        white coatings for interior wood
        -        indoor and outdoor paints
        -        industrial coatings
        -        cationic electrocoatings
        -        adhesives
        -        binders for non-woven fabrics
        -        textile printing
        -        artist's colours and primers
        -        paste tile-adhesives
        -        coatings for asbestos-cement

水乡的鱼

PLASTICIZER *  WP 8
非易失性，非水解
高分子增塑剂
简介：
PLASTICIZER *  WP 8是非挥发性，低粘度聚合物成膜剂，最初，专门开发用于塑化
丙烯酸聚合物。
由于其结构，增塑剂可湿性粉剂8将完全高耐水解性能，疏水性。
特性：
外观20°C清澈的液体
活性成分（%）100
沸点（℃）286
1.1密度。
C（CPS）60粘度。
闪点（开杯/℃）.
不溶于水中的溶解度
在MOS有机溶剂可溶
特性：
PLASTICIZER *  WP 8兼容的丙烯酸树脂，环氧树脂，醇酸树脂，聚酯和酚醛树脂，松香衍生物。
PLASTICIZER *  WP 8具有以下属性：
-优秀的伸长率和恢复
- 增加弹性和韧性
- 降低脆性
-非常低的水敏感性
改善薄膜的形成
-抗白粉病生长。
不像许多其他类型的增塑剂，PLASTICIZER *  WP 8不产生不利影响的粘附性，一致性，颜料结合力或丙烯酸乳液稳定性腻子包。它与丙烯酸分散体的相容性优良的允许相当大的纬度有关，可用于量。
根据应用程序的类型，PLASTICIZER *  WP 8可以从1%变化到更多，最终制定10%。
PLASTICIZER *  WP 8能力降低最低成膜温度（MFFT）如下：
应用：
PLASTICIZER *  WP 8主要用于以下应用：
-填缝剂、密封剂（见附配方）
-底漆/面漆的木材（见附配方））
室内木材白色涂料
-室内外涂料
工业涂料
阳离子电泳涂漆
-胶粘剂
无纺布粘合剂r
纺织印花
-艺术家的颜色和引物
粘贴瓷砖胶粘剂
石棉水泥涂料的研究

水乡的鱼

这款材料哪儿有买吗。